弱引力下小行星动量驱动机器人的可控跳跃行为

以小行星表面着陆探测为背景,提出一种动量驱动机器人(MoRo)以满足弱引力复杂环境下的探测需求。该机器人利用弱引力环境下的摩擦和碰撞特性,通过主动辨识环境参数,规划和控制动量轮以产生期望的驱动力矩,完成可控性跳跃及腾空后的稳定拍照等任务。首先,基于MoRo的动量轮刹车机构特性,分析了MoRo在弱引力环境下的跳跃机理并对其跳跃方式进行了规划;接着考虑动量轮驱动机构三闭环伺服系统的非线性特性,基于Herze碰撞模型和Karnopp摩擦模型建立了MoRo在小行星表面的跳跃行为动力学模型;其次,使用机器学习算法建立环境参数和MoRo运动的函数关系,并基于环境参数规划动量轮转速实现跳跃距离和腾空高度的可控。最后,通过数值仿真校验了MoRo跳跃规划方法和控制方法的可行性。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

Unsteady wakes-secondary flow interactions in a high-lift low-pressure turbine cascade

Detailed experimental measurements were conducted to study the interactions between incoming wakes and endwall secondary flow in a high-lift Low-Pressure Turbine (LPT) cascade. All of the measurements were conducted in both the presence and absence of incoming wakes, and numerical analysis was performed to elucidate the flow mechanism. With increasing Reynolds number, the influence of the incoming wakes on suppressing the secondary flow gradually increased owing to the greater influence of incoming wakes on reducing the negative incidence angle at higher Reynolds numbers, leading to a lower blade loading near the leading edge and suppression of the Pressure Side (PS) leg of the horseshoe vortex. However, the effect of unsteady wakes on suppressing the profile losses gradually became weaker owing to the reduced size of the Suction Side (SS) separation bubble and increased mixing loss in the free-flow region at high Reynolds numbers. Incoming wakes clearly improved the aerodynamic performance of the low-pressure turbine cascade at low Reynolds numbers of 25,000 and 50,000. In contrast, at the high Reynolds number of 100,000, the profile loss at the midspan and mass-averaged total losses downstream of the cascade were higher in the presence of wakes than in the absence of wakes, and the unsteady wakes exerted a negative influence on the aerodynamic performance of the LPT cascade.     

基于变马赫数的五孔探针三维插值方法

探讨了五孔探针气动数据的插值方法,为提高插值精度,开发了基于传统线性插值法的三维线性插值法。该方法把同一探针在不同马赫数下的校准图形成三维数据库,将实验数据通过三维图进行插值。并使用改进前后的两种插值方法分别对校准风洞测得的数据进行整理,对比结果证明:在实验工况连续变化的情况下,三维线性插值法在插值精度上要优于传统线性插值法。特别是在来流马赫数变化较大时,该方法可以改善单一校准文件处理造成的数据精度问题,可用于自动化流场采集系统,为流场高速高精度采集奠定基础。     

流动阻力及能量损失对注射成型制件的影响

本文分析了在塑料熔体充满型腔的过程中，流动阻力及能量损失产生的形式和物理原因，进而讨论了对塑料制件成型及凝固过程中的影响。并提出降低影响的措施。     

预测悬停旋翼跨音速流动的一种组合自由尾流/CFD方法

一种新的组合自由尾流 / CFD方法用于悬停旋翼流动的 CFD解中以考虑实际尾流的作用 .用文中描述的尾流分析方法研究了螺旋尖涡的运动 .首先从广义尾流模型开始 ,用半经验公式模化了涡核对旋翼尾流的作用 ;然后在环量收敛和尾迹收敛的条件下完成了自由尾迹计算 ;最后应用 Jameson有限体积龙格 -库塔推进格式求解了欧拉方程 .所得结果与相关文献和实验数据进行了比较     

ADI方法求解完全跨声速非定常小扰动方程

本文修改了Whitlow的ADI格式,以便求解另一变形的完全跨声速小扰动方程。本文给出的NACA64A006和NACA0012翼型的非定常跨声速流动的计算结果与其它数值结果和实验结果的比较表明本文格式是合理的且便于实际应用的。     

现代激励理论在规范地方政府行为中的作用研究

分析现代激励理论在研究地方政府行为中的作用，并运用现代激励理论提出了规范地方政府经济行为的若干建议。     

EFFECT OF THE RIBLETS SURFACE ON THE BOUNDARY LAYER DEVELOPMENT

ＥＦＦＥＣＴ　ＯＦ　ＴＨＥ　ＲＩＢＬＥＴＳ　ＳＵＲＦＡＣＥ　ＯＮ　ＴＨＥ　ＢＯＵＮＤＡＲＹ　ＬＡＹＥＲ　ＤＥＶＥＬＯＰＭＥＮＴＷａｎｇＪｉｎｊｕｎ；ＬａｎＳｈｉｌｏｎｇ；ＬｉａｎＱｉｘｉａｎｇ（ＩｎｓｔｉｔｕｔｅｏｆＦｌｕｉｄＭｅｃｈａｎｉｃｓＩＢｅ...